Keg Dispensing Supplies

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 1/4" straight barb to hook up to 1/4" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the 1/4" Quick Connect Insert, item #05P01-122.

German beer lovers rejoice! This "A" style German slider keg coupler, also known as a tap, is just what you need to get beer flowing from German kegs! This coupler is like no other, with a cupped mount that slides onto the keg and locks in place when engaged. This is the most widely used keg coupler in Germany, and while it will not work with all German beer kegs, it does work with most of them, as well as with a few Belgian kegs. Among the breweries that use the "A" coupler are Ayinger, Achouffe, Bitburger, Franziskaner, Hacker-Pschorr, Hoegaarden, Paulaner, Spaten, and Warsteiner. This coupler comes with the gas side connections, but does not include the liquid side connections which consist of a 3/16" liquid tailpiece, a beer nut and a neoprene washer.

Finally, a standard faucet made of above-standard material! These standard faucets are anything but standard, with full stainless steel bodies and levers. Stainless steel is the holy grail of beer materials! Sleek and stylist, it not only looks great, but is durable and will last longer than chrome or brass faucets. The simple design means that the faucets are easy to take apart and clean. For beer faucets that will last longer, stainless steel faucets can't be beat!

Bevlex tubing is a high quality thick-walled tubing. This 3/16" tubing works well for beer line, as it is the standard inner diameter for most serving systems. While the thinner walled tubing may also be used, this thick-walled tubing is recommended for permanent installations, such as on a kegerator or keezer dispensing system. It is also recommended when a thicker wall would come in useful. It is more durable and can withstand more pressure than the thinner-walled version.

Inner Diameter: 3/16 in.
Outer Diameter: 7/16 in.

Use this portable CO2 charger as a way to dispense beer from a Corny keg without dragging along your CO2 tank. No tanks. No hoses. It takes about two 16 gram non-threaded CO2 cartridges (Item # GF111, not included) to dispense a carbonated keg. Trigger valve allows precise control of gas. Charger connects directly to a gas ball or pin lock disconnect to dispense beer.

Do you often carbonate and serve beer at the same time? If so, or if you would like to be able to do both at different pressures, a secondary regulator is perfect for you! Your primary CO2 regulator attaches to your CO2 tank and allows one output pressure. However, a secondary regulator hooks up inline and allows you to regulate to another keg at a lower pressure. This allows you to carbonate one keg at a higher pressure while serving beer from another at a lower pressure! This Taprite secondary regulator is made to the same high standards as all Taprite equipment, with a high quality diaphragm that keeps regulating long after lesser regulators give up the ghost. Regulate at multiple pressures with a secondary regulator from Taprite!

You can never have too many disconnects! For all your pin lock draft needs, Great Fermentations offers you these liquid pin lock disconnects. Easy to take apart and clean, these have their uses not only in picnic taps, jockey boxes and home draft systems, but in a number of other brewing-related projects. These disconnects have a 1/4" MFL connection, which is perfect for attaching a swivel nut set for myriad applications. They have a plastic end on the male flare fitting so you don't have to use a plastic flare fitting washer when connecting them to metal. Make sure you have enough on hand for all the kegging and draft projects your mind can come up with!

The ball and pin lock disconnects used in kegging have a small washer that fits inside, creating a seal that allows the disconnects to properly allow for the flow of gas and liquid. Without this washer, you risk breaking the seal and causing all sorts of trouble with leaky disconnects! If your disconnect washers become damaged or go missing, you can simply replace them with these washers!

This CO2 shutoff with 1/4" MPT threading and check valve is ideal for use with CO2 regulators and manifolds! It has 1/4" MPT right-hand threading on one side that threads into most standard regulators and manifolds. On the other end is standard 1/4" MFL threading, which works perfectly with standard swivel nut sets and other 1/4" MFL fittings. If using a swivel nut set, we recommend using a plastic flare fitting as well, in order to create a good seal. Get one of these to replace a damaged or missing shutoff, put on a wye splittler, or create your own CO2 apparatus!

Don't give up on that old Perlick faucet, repair it! The Perlick repair kit was made for repairing the internals of a 425 series Perlick faucet, and comes with a stainless steel lever, a stainles steel plunger, and a chrome collar. These should be all the internal parts needed to repair a 425 Perlick. Breathe new life into that faucet with a repair kit!

A 4-way manifold is the perfect way to carbonate four kegs at once, or to pressurize kegs and run a Blichmann BeerGun at the same time! The CO2 can be hooked up from the regulator via the barb on the side of the manifold using standard 5/16" ID Bevlex tubing, and the other barbs can be run with the same tubing to gas disconnects for carbonating and dispensing from kegs, or to other CO2 driven devices. When mounted, the barbs run straight downward. Includes shutoff valves on the four top barbs on the manifold, which give another level of protection from lost CO2!

Superflush Tap & Line Cleaner is an safe, easy-to-use, economical and biodegradable line cleaner perfect for use on kegerators and draft dispensing systems. Simply mix 2-3 oz. with 1 gallon water as per the instructions and pump through lines. Allow to sit in lines for a few minutes, then flush clean with water. A solution made at the same rate may be used to clean faucet and coupler parts as well. Sold in a 32 oz bottle, Superflush can help you keep your lines pristine, pouring perfect beer every time!

This 5/16" tailpiece works with standard 5/16" ID CO2 tubing. Most often, these are found on the CO2 side of sanke couplers. Used in conjunction with a beer nut and a neoprene beer washer, these tailpieces can create a tight seal for CO2. Useful as a replacement on kegerator setups, make sure you have one on hand in your draft emergency kit!

A 3-way manifold is the perfect way to carbonate three kegs at once, or to pressurize kegs and run a Blichmann BeerGun at the same time! The CO2 can be hooked up from the regulator via the barb on the side of the manifold using standard 5/16" ID Bevlex tubing and worm clamps, and the other barbs can be run with the same tubing to gas disconnects for carbonating and dispensing from kegs, or to other CO2 driven devices. When mounted, the barbs run straight downward. Includes shutoff valves on the three top barbs on the manifold, which give another level of protection from lost CO2!

The Keg Line Cleaning Kit is the key to keeping your faucets, lines, and couplers clean. This kit includes a hand pump and cleaning solution container that attaches to your faucet shank, a 32 oz. bottle of Superflush Keg and Line Cleaner, a double ended faucet brush and a spanner wrench for removing faucets and attaching the cleaning pump.

Simply mix the Superflush Keg and Line Cleaner at the recommended rate of 2 to 3 oz. per gallon of water and use this solution to soak faucet and coupler parts. Remove the faucet from the shank using the spanner wrench, and attach the cleaning solution container to the shank with the spanner wrench. Pump solution through the liquid line and out into a bucket, then allow solution to sit in the lines for a few minutes. Fill the cleaning solution container with water and pump through to flush lines. Use the double ended brush to clean faucet and coupler, then flush with water and reassemble. Repeat when changing kegs to keep beer flowing free of foaming issues, beer stone buildup and bacterial infection.

This is a black plastic flange, the type that comes with standard beer shanks. It makes your custom kegerator look nice and professional, covering up drilled holes and providing a nice background for your beer faucet. If yours are damaged, replace them with this flange!

Is your tap handle too short? Not visible or prominently displayed, like you would like? Look no further than this chrome extension to solve your tap handle woes! This 1-inch chrome extension is placed between your faucet and tap handle to extend it outwards. Simple to use and effective, get the right length for your tap handle today!

This 3/16" tailpiece works with standard 3/16" ID liquid side tubing in a range of liquid dispensing applications. Most commonly, this tailpiece is used with a beer nut and a neoprene beer washer on the end of a shank as part of a faucet draft system. However, they are also used on sanke couplers for the liquid dispensing side. They can come in quite handy when replacing preinstalled liquid side connections in kegerators.

The original Guinness coupler! This keg coupler, popularly known as a tap, works on Guinness, Harp and Kilkenny kegs, as well as Smithwicks, Magners and a few select others. It is a "U" style keg coupler that is not commonly used by breweries, but is used by those mentioned. If you want to tap a keg of any of these, you will need a "U" coupler! This coupler includes the gas side connections. Not included is the a 3/16" liquid tailpiece, beer nut and neoprene washer.

Get that coupler into your kegerator! Some kegerators don't have a lot of clearance space, and a standard keg coupler won't fit on top of the keg. The solution to this problem? A low-profile sanke coupler! This coupler measures a mere 3.25", taking up less space above your keg than normal couplers. It has a unique design by which the engaging mechanism twists down the body and engages into the keg. Above the engaging body, the CO2 comes in the sideways barb, and liquid flows out sideways as well. Perfect for kegerator setup without a lot of vertical room! This coupler comes with an integrated gas barb. Not included is a 3/16" liquid tailpiece, beer nut and neoprene washer.

Rustproof wrench for CO2 nut on regulator. The right wrench, right where you need it, when you need it.